|
Ricer-X 05-10-2006, 07:06 PM http://i4.photobucket.com/albums/y124/Ricer-X/dscn2664.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2665.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2666.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2667.jpg Ricer-X 05-11-2006, 08:58 AM http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2668.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2669.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2670.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2671.jpg Ricer-X 05-11-2006, 08:58 AM http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2672.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2673.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2674.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2675.jpg Ricer-X 05-11-2006, 08:59 AM http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2677.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2678.jpg http://i4.photobucket.com/albums/y124/Ricer-X/DSCN2680.jpg Muzikman 05-11-2006, 03:11 PM Looks good. Just get some MT's on there. Maybe a front bumper with a winch and a rear bumper with a tire carrier. and you're all set. ;) Do you carry a floor jack everywhere you go? Ricer-X 05-11-2006, 03:28 PM yea, im too high for the factory jack, i actually broke it because of that, im just under 20" off the ground at the front jack point Muzikman 05-11-2006, 03:35 PM Time for some sliders and a hi-lift. :) Alley 05-11-2006, 04:40 PM Couldn't see these at work...grrr.... I definitly agree with the bigger more agressive tire need, I know its texas and you guys aren't fighting 6-7 inches of snow for three months. But, that thing kis just screaming for tires. Its too big for those street treads!! Ricer-X 05-11-2006, 05:24 PM my wheel size limits me though is the width of my wheels, im pretty sure they are only 7" wide, if they are 8" then i can go a bit bigger, but im not buying new wheels unless im puttin 35s on em midnight runner 05-13-2006, 01:29 AM looks good,, how many inches of lift and what company did you use and recommend... i want to lift my 06' X like 3 inches. But, I want to find a good reliable company for the lift and will I need to change anything like a steer arm or sort of parts to keep all angles right. or, can I crank the torsion bars in the front to lift it 3" and then just use something for the rear of the truck. I dont know too much and when I do this I want to make the right decisions from the beginning. THANKS FOR INPUT!! Muzikman 05-14-2006, 03:10 PM New generation X's don't have torsion bars. Currently there really isn't a way to raise it 3". You can gte 2.5 out of the Calmini and AC kits. You can get 2" out of the Daystar lift. Total Chaos just came out with their upper control arms (they cost $625). This should allow you to run larger spacers and get a bit more lift. Ricer-X. You can put 33x11.5 on the stock 7" wheels without a problem. You might even be able to go up to 33x12 as long as you don't air down much. | ||