Whats going on guys I...well not me but my girlfriend has a 2000 xterra 2wd bone stock and it needs attention to the ride height dept...she does not want to spend too much money who makes BL's for 2000's 2wd's she only wants like 2" thanks guy's

the only company i know that makes kits is performance

do a search in the DIY section for How To piece together a body lift...most people do that, and purchase the hardware and body spacers separately and only spend about $80 or so

oh, and welcome :)

im not too familiar with xterras but what kind of ifs do they have is it torsion bar system or coils or what

Welcome, where at in the Lone Star State?

Whats going on guys I...well not me but my girlfriend has a 2000 xterra 2wd bone stock and it needs attention to the ride height dept...she does not want to spend too much money who makes BL's for 2000's 2wd's she only wants like 2" thanks guy's

Did you want a BODY LIFT (BL), or, a SUSPENSION LIFT (SL)

You can get a 2" BL from AC

www.4x4parts.com

Its easier than piecing it together yourself, but ends up costing closer to $200 than $100 when all is said and done.

If you have the time and want to save ~ $100, there's a DIYS BL write up on this site.

:D

The X has torsion bars, with built-in adjusters, up front, and leaf springs out back.

You can add up to another 1.5" of front lift for free by adjusting them to raise the ride height.

You can raise the rear a matching 1.5" by adding a set of lift shackles (From the same place as the BL if convenient...)

You would need a new wheel alignment after that.

She could fit 33's if she got the 1.5" SL and the 2" BL described above.

32's will fit a stock X.

:D

Welcome to CX.

thanks

for now im only gonna go ahead and crank the t bars and do the shackles from ac looking for something quick and cheap...so with the pml i should be able to fit 32's right

thanks

for now im only gonna go ahead and crank the t bars and do the shackles from ac looking for something quick and cheap...so with the pml i should be able to fit 32's right

Correct Sir.

You will want to trim off the little plastic ledge at the rears of the front wheel wells. Its the little ledge the lower mud flaps used to screw to, but you don't need those anymore.

:D

That makes room for the rears of the tires to swing through on turns.

Its soft plastic, it snips right off in a coupla minutes per side, super easy.

I already KNOW you'll get a new wheel alignment after the lift, to restore handling and save the tires from excessive wear, etc.

:D

welcome

Welcome to Club Xterra.

_______________
Your Nissan Factory Warranty (http://www.vadennissanwarranty.com/nissan-factory-warranty.html) gives you basic coverage for 3 years or 36,000 miles on your Nissan. Have you explored what Nissan Extended Warranty (http://www.vadennissanwarranty.com/nissan-extended-warranty.html) coverage can do for your Nissan vehicle?

--Follow us on Twitter @NissanWarranty (http://Twitter.com/NissanWarranty)
--Got a Nissan Warranty question? Hit me up then I will post it to my Nissan Warranty Blog (http://blog.vadennissanwarranty.com/).
--For the latest Nissan Technical Service Bulletins (http://www.vadennissanwarranty.com/tsb/nissan/index.html). Subscribe (http://www.vadennissanwarranty.com/tsb/bulletins.rss.html?make=nissan)


Online since 2000.

Welcome to CX! from rockwall!

thanks for the info guy's....im pretty familiar with plastic trimming I used to own a 94 toyota 4runner on 33" Tsl's thanks for all...now were just waiting on her income tax check to get it done

thanks for the info guy's....im pretty familiar with plastic trimming I used to own a 94 toyota 4runner on 33" Tsl's thanks for all...now were just waiting on her income tax check to get it done

So is this the RedX I know from XRU?

Welcome from KY!